Flotec 1-12HP Cast Iron Sprinkler Pump - FP5172-08 1/2HP Cast Iron Sprinkler Pump Corrosion-resistant self-priming sprinkler pumps are constructed of rugged heavy-duty fiberglass-reinforced thermoplastic Capable of operating up to 30 sprinkler heads Self-priming design permits use on automatic sprinkling systems and also for de-watering and water transfer Rugged cast iron pump body construction Heavy duty motor 115/230 voltage U L and CSA approved Stainless steel shaft Capacitor start Sealed bearings Can clean out or remove components while pump body remains in place High head 1-1/2 HP delivers up to 65 gallons per minute or up to 120 total feet in head Suction lift up to 25 Once filled with water the pump will self prime Fast priming Operate larger sprinkler zones Up to thirty 1-1/2 GPM sprinkler heads Contractor Commercial agriculture and industrial use De-Watering Water transfer Stock watering Fire protection U L Listed PRODUCT FEATURES Superior performance at depths to water of 25 or less Ideal for larger sprinkler zones or water transfer Rugged cast iron pump housing Self-priming after pump housing is initially filled Check Valve or Foot Valve required Heavy-duty A O Smith motor Ready-to-install 230 volt motor See manual for 115 volt conversion Fully serviceable unit PRODUCT SPECIFICATION
Flotec 10 Gallon per Minute Shallow Well Jet Pump - FP4022-08 10 Gallon per Minute Shallow Well Jet Pump For wells with pumping levels of 25 or less Self-priming after the pump housing is initially filled with water Built-in shallow well jet has corrosion-resistant nozzle and venturi Fiberglass-reinforced thermoplastic provides total corrosion resistance and high resistance to sandy water Dust-proof cover to protect all electrical components from dust and insects Motor features stainless steel shaft heavy-duty ball bearings balanced rotor mechanical shaft seal and insulated motor windings Pre-set pre-wired pressure switch for automatic operation when used with water systems tank Top discharge 1-1/4 in NPT suction and 3/4 in NPT discharge pipe sizes Dual voltage 115/230V factory set at 230V Wiring diagrams are permanently affixed on each motor for easy field change to 115 volt Pressure switch setting 30-50 U L Listed
Flotec 12HP Cast Iron Sprinkler Pump - FP5242 1-1/2HP Cast Iron Sprinkler Pump Corrosion-resistant self-priming sprinkler pumps are constructed of rugged heavy-duty fiberglass-reinforced thermoplastic Capable of operating up to 30 sprinkler heads Self-priming design permits use on automatic sprinkling systems and also for de-watering and water transfer Fast corrosion resistant constructed of rugged heavy duty fiberglass-reinforced thermoplastic Ideal for lawn sprinkling applications Capable of operating up to 30 sprinkler heads The self-priming design permits use on automatic sprinkling systems and also for de-watering and water transfer Heavy duty designed for continuous operation Motors have stainless steel shaft heavy duty bearings and dust-proof cover to eliminate the most common cause of motor failure Easy service design for quick access to normal wearing parts No FP5172 - Dual voltage motor set at 230V with Owners Manual instructions for changing to 115V PRODUCT FEATURES Superior performance at depths to water of 20 or less Fiberglass-reinforced thermoplastic pump housing for the highest corrosion resistance Heavy-duty A O Smith motor Ready-to-install 230 volt motor See manual for 115 volt conversion Self-priming after pump housing is initially filled Check Valve or Foot Valve required Fully serviceable unit TC2104 pressure gauge recommended PRODUCT SPECIFICATION
Flotec 12HP Cast Iron Submersible Sump Pump with Float Switch - FPOS3200A-08 1/2HP Cast Iron Submersible Sump Pump with Float Switch Corrosion and abrasion resistant with a screened top inlet and has an oil-cooled high torque 115V motor with automatic overload protection Standard 8 grounded power cord automatic float and has a 1-1/4 in discharge Float switch on 14 in off 6 in Minimum sump diameter 14 in U L Listed
Flotec 13HP Cast Iron Submersible Sump Pump with Float Switch - FP0S2400A-08 1/3HP Cast Iron Submersible Sump Pump with Float Switch Corrosion and abrasion resistant with a screened top inlet and has an oil-cooled high torque 115V motor with automatic overload protection Standard 8 grounded power cord automatic float and has a 1-1/4 in discharge Float switch on 14 in off 6 in Minimum sump diameter 14 in U L Listed
Flotec 13HP Cast Iron Submersible Sump Pump with Vertical Switch - FPSC2250A Cast iron automatic submersible sump pumps are constructed of rugged cast iron with a screened bottom inlet Each has an oil-cooled high torque 115V motor with automatic overload protection
Flotec 13HP Thermoplastic Pedestal Sump Pump - FPPM3600D-08 1/3HP Thermoplastic Pedestal Sump Pump Corrosion-resistant construction features plastic volute impeller and column Replaces any existing brand of pedestal pump Top inlet prevents loose debris in sump pit from entering pump Industry standard mechanical switch for easy service Motor with automatic thermal overload protection Power cord 6 with 3-prong grounded plug 1-1/4 in discharge
Flotec 14HP Cast Iron Submersible Sump Pump with Float Switch - FP0S1800A-08 1/4HP Cast Iron Submersible Sump Pump with Float Switch Corrosion and abrasion resistant with a screened top inlet and has an oil-cooled high torque 115V motor with automatic overload protection Standard 8 grounded power cord automatic float and has a 1-1/4 in discharge Float switch on 12-1/2 in off 4-1/2 in Minimum sump diameter 14 in U L Listed 1-1/4 in inside thread with a 1-1/2 in outside thread for maximum versatility on replacement jobs
Flotec 14HP Intellipump Thermoplastic Utility Pump - FPOS1775A Electronic controlled submersible pump automatically turns on when water is present and turns off at 3/16 in Portable and lightweight For surfaces that collect water such as basements rooftops window wells or any shallow flooded area Maximum pumping capacity to 1790 gallons per hour Corrosion-resistant engineered construction One time plug-in installation Includes 15 power cord and garden hose adapter
Flotec 16HP Thermoplastic Utility Pump - FP0S1250X-08 1/6HP Thermoplastic Utility Pump This non-corrosive high strength thermoplastic utility pump is lightweight and portable Ideal for sump pumping draining window wells and cisterns and recirculating waterfalls and decorative fountains Pumps to 1 140 GPH bottom suction pumps down to 3/16 in Continuous duty oil-cooled motor has overload protection 8 grounded replaceable power cord Includes garden hose adapter 1 in NPT discharge UL Listed
Flotec 2" x 15' Pump Suction Hose Kit with Fittings - FP2735 2 in x 15 Pump Suction Hose Kit with Fittings Pump suction hose kit with fittings and suction screen
Flotec 2-Wire 4" Submersible Well Pump - FP22 2-Wire 4 in Submersible Well Pump For 4 in inside diameter or larger wells Pumps from depths of 400 ft Floating stack design for sand resistance and reduced sand locking Corrosion-resistant stainless steel pump and motor housing Heavy-duty discharge connection Precision-molded impellers and diffusers Includes built-in check valve Water filled submersible motor 1-1/4 in NPT
Flotec 42 Gallon Pressure Tank - FP7230-08 42 Gallon Pressure Tank Replaces any standard galvanized glass-lined or epoxy-lined tank Precision press fit design minimizes gaps between components reducing the possibility of corrosion and seam leaks Heavy gauge all steel construction Powder epoxy interior coating electrostatically applied Tough polyester exterior paint Standard air volume control tap Excellent corrosion resistant tank for home water systems applications such as retention tank holding tank and pressure tank The epoxy interior coating is resistant to corrosion and is FDA listed
Flotec 6 Gallon Pressure Tank - FP7105-00 6 Gallon Pressure Tank Air valve enables installer to reduce pre-charge pressure to match pressure switch setting Tank is factory pre-charged to 40 PSI Universal mounting bracket may be used with any jet pump not included Rugged tank body is constructed of heavy-gauge steel Tank exterior features durable baked-on finish to provide maximum corrosion resistance A replaceable air/water separator of rugged seamless vinyl prevents ``water logging in of the tank This helps to prolong pump life Separator not shown is constructed of FDA-approved materials will not cause taste or odor water problems Well water never touches metal in tank Certified to ANSI/NSF Standard 61 Pre-charged ``Rated in 6 gallon tank 8 in diameter x 13 in H 3/4 in discharge tapping
Flotec 8 Gallon per Minute Shallow Well Jet Pump - FP4012-08 8 Gallon per Minute Shallow Well Jet Pump For wells with pumping levels of 25 or less Self-priming after the pump housing is initially filled with water Built-in shallow well jet has corrosion-resistant nozzle and venturi Fiberglass-reinforced thermoplastic provides total corrosion resistance and high resistance to sandy water Dust-proof cover to protect all electrical components from dust and insects Motor features stainless steel shaft heavy-duty ball bearings balanced rotor mechanical shaft seal and insulated motor windings Pre-set pre-wired pressure switch for automatic operation when used with water systems tank Top discharge 1-1/4 in NPT suction and 3/4 in NPT discharge pipe sizes Dual voltage 115/230V factory set at 230V Wiring diagrams are permanently affixed on each motor for easy field change to 115 volt Pressure switch setting 30-50 U L Listed
Flotec 8.5 Gallon per Minute Shallow Well Jet Pump - FSNCH-L 8 5 Gallon per Minute Shallow Well Jet Pump For wells with pumping levels of 25 or less Self-priming after the pump housing is initially filled with water Built-in shallow well jet has corrosion-resistant nozzle and venturi Fiberglass-reinforced thermoplastic provides total corrosion resistance and high resistance to sandy water Dust-proof cover to protect all electrical components from dust and insects Motor features stainless steel shaft heavy-duty ball bearings balanced rotor mechanical shaft seal and insulated motor windings Pre-set pre-wired pressure switch for automatic operation when used with water systems tank Top discharge 1-1/4 in NPT suction and 3/4 in NPT discharge pipe sizes Dual voltage 115/230V factory set at 230V Wiring diagrams are permanently affixed on each motor for easy field change to 115 volt Pressure switch setting 30-50 U L Listed
Flotec Multi Purpose Drill Pump - FPDMP21SA Multi Purpose Drill Pump Works with any electric drill MINIMUM DRILL SPEED 1200 RPM For emergency pumping emptying stopped-up sinks and kitchen appliances draining aquariums and waterbeds pumping out furnace pits and window wells changing oil in cars and inboard marine engines transferring lubricants and non-flammable liquids Pumps to 216 GPH Self-priming to 8 vertical lift Discharges up to 40 vertically or 200 horizontally when using 5/8 in I D garden hose Pressure-lubricated shaft bearing and seal
Flotec Sump Pump Float Switch with Piggyback Plug - FP18-15BD Sump Pump Float Switch with Piggyback Plug Replacement float switch for all sump pumps with automatic floats 8 cord length
Hydromatic Battery Back-Up Power Supply with B-A1 Pump - Aplus Battery Back-Up Power Supply with B-A1 Pump PRODUCT FEATURES Battery not Included Automatically charges the battery Runs the pump off of line power when available avoiding unnecessary battery drain down Three indicator lights tell you the status of the system at all times Electronics are fan cooled for optimum efficiency and reliability Non-corrosive battery case Power coated electronics enclosure for maximum durability and corrosion resistance Automatically checks for restored power in the AC line every five minutes Made in the USA PUMP SPECIFICATION Pump/Motor Unit B-A1 Submersible Sump Pump Horsepower 1/4 Full Load Amps 6 5 Motor Type PSC R P M 3450 Voltage 115 Hertz 60 Temperature 105 Degrees C Insulation Class A Discharge Size 1-1/2 in NPT Solids Handling 1/4 in Power Cord SJTW 10 std Minimum Recommended Sump Diameter Simplex = 18 in 457mm Duplex = 30 in 762mm Automatic Operation Wide angle float switch Handle Thermoplastic Lubricating Oil Dielectic Oil Motor Housing Cast Iron Shaft Steel Seal Faces Carbon/Ceramic Seal Body Anodized Steel Spring Stainless Steel Bellows Buna-N Impeller Thermoplastic Upper/Lower Bearing Ball Bearing Bottom Plate Thermoplastic Fasteners Stainless Steel PRODUCT SPECIFICATION Includes B-A1 sump pump Shipping Weight 35
Hydromatic Condensate Pump - HC20 Condensate Pump The Hydromatic HC20 Condensate unit is designed to automatically remove the liquid from an air conditioner evaporative coil and/or a gas condensing warm air furnace This unit is made from a tough ABS plastic so it will resist corrosion and impacts PRODUCT FEATURES Check valve to prevent backflow of liquid into the unit and overflow safety switch For indoor use only UL and cUL listed PRODUCT SPECIFICATION Pump Type Condensate Pump Pump Model HC20 Capacities up to 95 GPH Heads up to 20ft Liquids Drain water Tank compacities 2 0 Quarts Temperature 190¾F Full Load Amps 1 45 Voltage 115 Hertz 60 Unit weight 3 25 lb Housing Thermoplastic Power Cord 6 ft Shipping Weight 3 25
Hydromatic Pedestal Sump Pump - P33A1 Pedestal Sump Pump PRODUCT FEATURES Dependable 1/3 HP motor Easily adjustable pumping range Non-corrosive volute/base and impeller Automatic reset thermal overload protection PRODUCT SPECIFICATION Pump/Motor Unit Submersible Sump Pump Capacities up to 54 GPM 3 4 l/s Heads up to 18ft 7 0m Electrical 115V 6 5FLA 60Hz Motor 3 HP Shaded Pole 1725 RPM Minimum Recommended Sump Diameter 12 in 304 8mm Automatic Operation Mechanical float with rod Materials of Constriction Engineered thermoplastic Impeller Thermoplastic vortex Discharge size 1-1/4 in NPT 31 8mm Solids handling 1/4 in 6 4mm Power cord 8 16/3 SJT Shipping Weight 18
Hydromatic Plastic Submersible Sump Pump with Wide Angle Float Switch - B-A1 Plastic Submersible Sump Pump with Wide Angle Float Switch PRODUCT FEATURES Carbon/Ceramic mechanical seal Uses a single rowball bearing construction Piggy-back plug available for easy maintenance and replacement 1/4 HP 3450 RPM motor powers the vane type semiopen impeller for high efficiency Oil-filled motor for heat dissipation and continuous lubrication Mechanical shaft seal assures reliable operation Cast iron motor housing PRODUCT SPECIFICATION Pump/Motor Unit Submersible Sump Pump Horsepower 1/4 Full Load Amps 6 5 Motor Type PSC R P M 3450 Voltage 115 Hertz 60 Temperature 105 Degrees C Insulation Class A Discharge Size 1-1/2 in NPT Solids Handling 1/4 in Power Cord SJTW 10 std Minimum Recommended Sump Diameter Simplex = 18 in 457mm Duplex = 30 in 762mm Automatic Operation Wide angle float switch Handle Thermoplastic Lubricating Oil Dielectic Oil Motor Housing Cast Iron Shaft Steel Seal Faces Carbon/Ceramic Seal Body Anodized Steel Spring Stainless Steel Bellows Buna-N Impeller Thermoplastic Upper/Lower Bearing Ball Bearing Bottom Plate Thermoplastic Fasteners Stainless Steel Unit Weight 15lbs Shipping Weight 15lbs
Hydromatic Sewage Ejector Pump Package - JB-1-100 Sewage Ejector Pump Package PRODUCT FEATURES Accommodates toilet vanity humidifier or shower Fits almost anywhere Use with many toilet styles Perfect for basement family rooms warehouses factories room additions JB-1 can be installed free standing on any level surface or the tank and all piping can be hidden behind a wall and under the floor No need to destroy concrete floor JB-1 can be installed free standing on any level surface Easily installed Shipping Weight 90lbs PRODUCT INCLUDES Tank lid amp gasket SKV40JBA 4/10 HP sewage pump Back flow device check local codes 2 discharge amp 2 vent flanges with bolt down seals Installation instructions PUMP SPECIFICATIONS Model SKV40JBA 4/10 HP 115v 11 amps 230v 5 amps Split Phase Weight 35 lbs Automatic preset float switch with piggy backstyle plug-in Thermal overload protected motor Stainless steel screws bolts amp handle Non-clogging vortex impeller Passes 2 spherical solids CSA listed 3-wire neoprene 10 ft cord amp plug Max temperature rating - 130° F 54° C
Hydromatic Sewage Ejector Pump with Wide Angle Float Switch - SKV40AW1 Sewage Ejector Pump with Wide Angle Float Switch PRODUCT FEATURES Cabon/Ceramic type 21mechanical seal Oil filled motor with automatic reset thermal overload protection Lower single rowball bearing construction Recessed vortex impeller allows pumping of stringy material and reduces clogging Piggy-back plug available for easy maintenance and replacement PRODUCT SPECIFICATION Capacity up to 78 GPM 4 9 l/s Heads up to 19 5ft 5 9m Electrical 115V 12 6 FLA 60hz Motor 4/10 HP split phase w/ thermal overload protection 1750 RPM Minimum Recommended Sump Diameter Simplex 18 in 457mm Duplex 30 in 762mm Automatic Operation Wide Angle Float Switch Materials of Construction Class 30 cast iron engineered thermoplastic Impeller Thermoplastic recessed vortex Discharge Size 2 in 50 8mm Solids Handling 2 in 50 8mm Power Cord 10 SJTW Shipping Weight 32lbs
Hydromatic Utility Pump - HUP Utility Pump PRODUCT FEATURES Easy to use most anywhere and weights only 7 lb Attach a standard hose to pump discharge and plug into any 115V outlet Removes standing water down to 1/8 in depth CSA and UL listed PRODUCT SPECIFICATION Pump Type Utility Pump Pump Model HUP Capacities up to 20 GPM Heads up to 22ft 6 4m Solids Handling Capacity 1/8 in 3 18mm Liquids Handling Drain Water Itermittent Liquid Temp Up to 140¾F Up to 60¾C Motor 1/6 HP P S C Electrical 115V 2 amps 1¸ 60Hz Acceptable ph Range 6-9 Discharge Hose Adapter 1 in 25 4 mm Turn-On/Turn-Off Manually Controlled Housing Thermoplastic Power Cord SJTW or SJTW-A 10 ft Mechanical Seal Carbon and Ceramic
Jacuzzi Brothers 1 HP 12GPM 2 Wire Sumbersible Well Pump - R10SUB122 (By:-Jacuzzi Brothers) 4 in submersible pumps deliver excellent performance for wells up to 440 depths PumpWorks 4 in submersible pumps are available in 1/2 3/4 1 and 1 1/2 HP in both two and three wire configurations Also available in 115 volt two wire model 1/2 HP only
Jacuzzi Brothers 1 HP 5GPM 2 Wire Sumbersible Well Pump - R10SUB52 (By:-Jacuzzi Brothers) 4 in submersible pumps deliver excellent performance for wells up to 440 depths PumpWorks 4 in submersible pumps are available in 1/2 3/4 1 and 1 1/2 HP in both two and three wire configurations Also available in 115 volt two wire model 1/2 HP only
Jacuzzi Brothers 1 HP 8GPM 2 Wire Sumbersible Well Pump - R10SUB82 (By:-Jacuzzi Brothers) 4 in submersible pumps deliver excellent performance for wells up to 440 depths PumpWorks 4 in submersible pumps are available in 1/2 3/4 1 and 1 1/2 HP in both two and three wire configurations Also available in 115 volt two wire model 1/2 HP only
Jacuzzi Brothers 1-12 HP 12GPM 2 Wire Sumbersible Well Pump with Control Box - R15SUB122 (By:-Jacuzzi Brothers) 4 in submersible pumps deliver excellent performance for wells up to 440 depths PumpWorks 4 in submersible pumps are available in 1/2 3/4 1 and 1 1/2 HP in both two and three wire configurations Also available in 115 volt two wire model 1/2 HP only
Jacuzzi Brothers 12 HP 12GPM 2 Wire Sumbersible Well Pump - R5SUB122-1 (By:-Jacuzzi Brothers) 4 in submersible pumps deliver excellent performance for wells up to 440 depths PumpWorks 4 in submersible pumps are available in 1/2 3/4 1 and 1 1/2 HP in both two and three wire configurations Also available in 115 volt two wire model 1/2 HP only
Jacuzzi Brothers 12 HP 12GPM 2 Wire Sumbersible Well Pump - R5SUB122 (By:-Jacuzzi Brothers) 4 in submersible pumps deliver excellent performance for wells up to 440 depths PumpWorks 4 in submersible pumps are available in 1/2 3/4 1 and 1 1/2 HP in both two and three wire configurations Also available in 115 volt two wire model 1/2 HP only
Jacuzzi Brothers 12 HP 5GPM 2 Wire Sumbersible Well Pump - R5SUB52 (By:-Jacuzzi Brothers) 4 in submersible pumps deliver excellent performance for wells up to 440 depths PumpWorks 4 in submersible pumps are available in 1/2 3/4 1 and 1 1/2 HP in both two and three wire configurations Also available in 115 volt two wire model 1/2 HP only
Jacuzzi Brothers 12 HP 8GPM 2 Wire Sumbersible Well Pump - R5SUB82 (By:-Jacuzzi Brothers) 4 in submersible pumps deliver excellent performance for wells up to 440 depths PumpWorks 4 in submersible pumps are available in 1/2 3/4 1 and 1 1/2 HP in both two and three wire configurations Also available in 115 volt two wire model 1/2 HP only
Jacuzzi Brothers 14 HP Thermoplastic Sump Pump - PS25A (By:-Jacuzzi Brothers) The PS Series Sump Pumps are extremely quiet and efficient using the sump water instead of oil for cooling the sump motor
Jacuzzi Brothers 34 HP 5GPM 2 Wire Sumbersible Well Pump - R7SUB52 (By:-Jacuzzi Brothers) 4 in submersible pumps deliver excellent performance for wells up to 440 depths PumpWorks 4 in submersible pumps are available in 1/2 3/4 1 and 1 1/2 HP in both two and three wire configurations Also available in 115 volt two wire model 1/2 HP only
Jacuzzi Brothers 34 HP 5GPM 3 Wire Sumbersible Well Pump with Control Box - R7SUB53 (By:-Jacuzzi Brothers) 4 in submersible pumps deliver excellent performance for wells up to 440 depths PumpWorks 4 in submersible pumps are available in 1/2 3/4 1 and 1 1/2 HP in both two and three wire configurations Also available in 115 volt two wire model 1/2 HP only
Jacuzzi Brothers 34 HP 8GPM 2 Wire Sumbersible Well Pump - R7SUB82 (By:-Jacuzzi Brothers) 4 in submersible pumps deliver excellent performance for wells up to 440 depths PumpWorks 4 in submersible pumps are available in 1/2 3/4 1 and 1 1/2 HP in both two and three wire configurations Also available in 115 volt two wire model 1/2 HP only
Wayne Pumps 1 HP Portable Lawn Sprinkler Utility Pump - PLS100 (By:-WaynePumps) This pump is designed to sprinkle lawns and small gardens from lakes ponds or rivers empty or fill stock tanks remove standing water from flooded areas and transfer water
Wayne Pumps 115 Volt Transfer Pump - PC2 (By:-WaynePumps) Includes 6 suction hose water suction attachment and replacement parts kit 66058-WYN1 PC2 brush and impeller kit sold seperately
Wayne Pumps 12 HP Cast Iron Submersible Sump Pump With Float Switch - CDU800 (By:-WaynePumps) The CDU800 features a cast iron housing for long life and quiet operation This submersible pump is compactly designed for 11 in or larger sump pits
Wayne Pumps 12 HP Corrosion-Resistant Pedestal Sump Pump - PTU50 (By:-WaynePumps) The PTU series pumps are value-priced pedestal sump pumps that provide consumers with an economic solution to helping to keep their basement dry
Wayne Pumps 12 HP Corrosion-Resistant Submersible Sump Pump With Float Switch - SPF50 (By:-WaynePumps) Models SPF33 and SPF50 with mechanical float switch install in sump pits as small as 11 in diameter Compact size insures these full featured pumps are ideal replacements for most pedestal and submersible sump pumps
Wayne Pumps 12 Volt Transfer Pump - PC1 (By:-WaynePumps) Includes 6 suction hose water suction attachment and replacement parts kit 66052-WYN1 PC1 brush and impeller kit sold seperately
Wayne Pumps 16 HP Oilless Submersible Utility Water Pump - RUP160 (By:-WaynePumps) The Wayne RUP 160 is an oilless high volume capacity submersible utility pump The 1/6 HP motor pumps up to 2000 gallons per hour This pump also features an energy efficient motor that can start even when plugged into longer power lines and cords The discharge port can accept 1 1/4 in high volume hose or standard garden hose
Wayne Pumps 34 HP Cast Iron & Stainless Steel Submersible Sump Pump With Float Switch - CDU-980 (By:-WaynePumps) Wayne s CDU980 features stainless steel housing for superior corrosion resistance and a durable cast iron pump for long life This submersible unit is designed for basements with frequent water problems High flow rates plus rugged components stand up to tough conditions year after year
Wayne Pumps 4 HP Semi-Trash Utility Pump - GPH400 (By:-WaynePumps) Wayne s gas engine pumps can be carried virtually anywhere for irrigation dewatering agricultural chemical transfer and much more
Wayne Pumps CDU790 13 HP Cast Iron Submersible Sump Pump With Float Switch - 56137-WYN3 (By:-WaynePumps) The CDU790 features durable cast iron housing for long life and quiet operation This submersible pump is compactly designed for 11 in or larger sump pits
Wayne Pumps ESP15 12V Standby Sump Pump System - 57609-WYN1 (By:-WaynePumps) Every homeowner with a sump pump should consider the possibility of a power failure which is most likely to occur when it s raining This 12V standby system takes over automatically to help protect against flood damage when the power fails
Wayne Pumps GP300 3.5 HP Transfer Utility Pump - 56681 (By:-WaynePumps) Wayne s gas engine pumps can be carried virtually anywhere for irrigation dewatering agricultural chemical transfer and much more
Wayne Pumps PC4 12 HP Portable Electric Utility Pump - 55832 (By:-WaynePumps) Model PC4 can be used to pump water from flooded basements empty boats drain stock tanks or water lawns and gardens It can also be used to boost line pressure by as much as 40 lbs For power washing cars sidewalks and more A suction strainer is included with each pump
Wayne Pumps SPF33 13 HP Thermoplastic Corrosion-Resistant Submersible Sump Pump With Float Switch - 57610-WYN1 (By:-WaynePumps) Models SPF33 and SPF50 with mechanical float switch install in sump pits as small as 11 in diameter Compact size insures these full featured pumps are ideal replacements for most pedestal and submersible sump pumps
Wayne Pumps SPT33 13 HP Corrosion-Resistant Submersible Sump Pump With Tether Switch - 57600-WYN1 (By:-WaynePumps) Model SPT33 and SPT50 feature mercury-free tethered switches that are adjustable for various on/off levels Model SPT33 features a high performance 1/3 HP motor Model SPT50 has a heavy duty 1/2 HP motor providing maximum performance for heavy duty applications
Wayne Pumps TSC130 14 HP Submersible Utility Pump - 56517 (By:-WaynePumps) Wayne s TSC utility pumps are water cooled for best performance in continuous duty applications such as draining flooded basements emptying water-filled boats and removing water from sinks tubs stock tanks and flat roofs
Wayne Pumps VIP15 15 HP Vortex Submersible Utility Pump - 57700-WYN1 (By:-WaynePumps) This unique utility pump passes 1/2 in solids such as leaves pebbles and other debris without clogging
New Home in Vermont from Snyder Companies. Now building in Milton and South Burlington. For over twenty years, The Snyder Companies have earned a reputation for building quality homes in the most desirable communities in Vermont. ... we have a broad range of counter top, cabinet, plumbing features, appliances and many other selections to choose from ...
